View ADP1109A_82140.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

a
FEATURES Operates at Supply Voltages 2 V to 9 V Fixed 3.3 V, 5 V, 12 V and Adjustable Output Minimum External Components Required Ground Current: 460 A Oscillator Frequency: 120 kHz Logic Shutdown 8-Lead DIP and SO-8 Packages APPLICATIONS Cellular Telephones Single-Cell to 5 V Converters Laptop and Palmtop Computers Pagers Cameras Battery Backup Supplies Portable Instruments Laser Diode Drivers Hand-Held Inventory Computers
Micropower Low Cost Fixed 3.3 V, 5 V, 12 V and Adjustable DC-to-DC Converter ADP1109A
FUNCTIONAL BLOCK DIAGRAM
VIN SENSE R2 250k COMPARATOR 1.25V REFERENCE A1 120kHz OSCILLATOR DRIVER Q1
ADP1109A-3.3: R1 = 152k ADP1109A-5: R1 = 83k ADP1109A-12: R1 = 29k
SW
R1
GND
SHUTDOWN
PGND
VIN
FB
ADP1109A
COMPARATOR
SW 120kHz OSCILLATOR DRIVER
GENERAL DESCRIPTION
1.25V REFERENCE
A1
Q1
The ADP1109A is a versatile step-up switching regulator. The device requires only minimal external components to operate as a complete switching regulator. The ADP1109A-5 can deliver 100 mA at 5 V from a 3 V input and the ADP1109A-12 can deliver 60 mA at 12 V from a 5 V input. The device also features a logic controlled shutdown capability that, when a logic low is applied, will shut down the oscillator. The 120 kHz operating frequency allows for the use of small surface mount components. The gated oscillator capability eliminates the need for frequency compensation.
GND SHUTDOWN
PGND
TYPICAL APPLICATION
L1 33 H D1
3
VIN 5V
1
VIN
SW
SENSE 8
ADP1109A-12
7
VOUT 12V 60mA
SHUTDOWN PGND GND
4 5
+
SHUTDOWN/PROGRAM
C1 22 F 16V
Flash Memory VPP Generator
REV. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 1997
ADP1109A-SPECIFICATIONS (0 C T 70 C, V
A
IN
= 3 V unless otherwise noted)
VS IQ VIN 2 1.20 1.25 8 VOUT 3.13 4.75 11.45 3.30 5.00 12.00 15 25 60 fOSC 95 57 3.8 120 67 5.6 0.4 0.4 0.4 1 VIH VIL 2.0 0.8 10 20 Min Typ 460 Max 580 9 1.30 12.5 3.47 5.25 12.55 35 50 120 155 77 7.4 0.8 0.8 0.8 10 Units A V V mV V V V mV mV mV kHz % s V V V A V V A A
Parameter QUIESCENT CURRENT INPUT VOLTAGE COMPARATOR TRIP POINT VOLTAGE COMPARATOR HYSTERESIS OUTPUT VOLTAGE ADP1109A-3.3 ADP1109A-5 ADP1109A-12 OUTPUT VOLTAGE RIPPLE
Conditions Switch Off
ADP1109A 2 V VIN 3 V 2 V VIN 5 V 2 V VIN 9 V ADP1109A-3.3 ADP1109A-5 ADP1109A-12
OSCILLATOR FREQUENCY DUTY CYCLE SWITCH-ON TIME SWITCH SATURATION VOLTAGE ADP1109A-3.3 ADP1109A-5 ADP1109A-12 SWITCH LEAKAGE CURRENT SHUTDOWN PIN HIGH SHUTDOWN PIN LOW SHUTDOWN PIN INPUT CURRENT SHUTDOWN PIN INPUT CURRENT VSHUTDOWN = 4 V VSHUTDOWN = 0 V ISW = 500 mA VIN = 3 V VIN = 3 V VIN = 3 V VSW = 9 V, TA = +25C Full Load
DC tON VCESAT
IIH IIL
NOTES All limits at temperature extremes are guaranteed via correlation using standard quality control methods. Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage, VOUT . . . . . . . . . . . . . . . . . . . . -0.4 V to 20 V SW Pin Voltage . . . . . . . . . . . . . . . . . . . . . . . . -0.4 V to 50 V Shutdown Pin Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0 V Switch Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 A Maximum Power Dissipation . . . . . . . . . . . . . . . . . . 300 mW Operating Temperature Range . . . . . . . . . . . . 0C to +70C Storage Temperature Range . . . . . . . . . . . . -65C to +150C Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . +300C
*This is a stress rating only; operation beyond these limits can cause the device to be permanently damaged.
-2-
REV. 0
ADP1109A
PIN FUNCTION DESCRIPTIONS PIN CONFIGURATIONS 8-Lead Plastic DIP (N-8)
VIN 1 NC
2 8
Pin Mnemonic 1 2 3 4 5 6 7 8 VIN NC SW PGND GND NC SHUTDOWN FB(SENSE)
Function Input Supply Voltage. No Connection. Collector Node of Power Transistor. Power Ground. Ground. No Connection. When logic low is applied to this pin, oscillator is shut down. On the ADP1109A (Adjustable), this pin goes directly to the comparator input. On the ADP1109A-3.3, ADP1109A-5 and ADP1109A-12, this pin is connected through the internal resistor that sets the output voltage.
ORDERING GUIDE
FB(SENSE)*
SHUTDOWN TOP VIEW SW 3 (Not to Scale) 6 NC PGND 4
5
ADP1109A
7
GND
*FIXED VERSIONS NC = NO CONNECT
8-Lead SOIC (SO-8)
VIN 1 NC 2 SW 3 PGND 4
8
FB(SENSE)* SHUTDOWN NC GND
ADP1109A
TOP VIEW (Not to Scale)
7 6 5
Model ADP1109AAN ADP1109AAR ADP1109AAN-3.3 ADP1109AAR-3.3 ADP1109AAN-5 ADP1109AAR-5 ADP1109AAN-12 ADP1109AAR-12
Output Voltage ADJ ADJ 3.3 V 3.3 V 5V 5V 12 V 12 V
Package Description Plastic DIP Small Outline IC Plastic DIP Small Outline IC Plastic DIP Small Outline IC Plastic DIP Small Outline IC
Package Options N-8 SO-8 N-8 SO-8 N-8 SO-8 N-8 SO-8
*FIXED VERSIONS NC = NO CONNECT
CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADP1109A features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. 0
-3-
ADP1109A
2k 20 H* VIN 3.3V 22 F +
3 1
MBRS130T3 12V 60mA VIN 5V +
10 H* 22 F
MBRS130T3 2N4403
3
VIN
SW
SENSE 8
1
VIN
SW
SENSE 8
ADP1109A-12
7
ADP1109A-12
7
SHUTDOWN GND PGND
5 4
+
SHUTDOWN GND PGND
5 4
VOUT 12V 110mA + +
33 F** 25V SHUTDOWN
47 F** 20V
1F
SHUTDOWN *COILTRONICS CTX20-1 SUMIDA CD54-220LC **AVX TPS SERIES
*COILTRONICS CTX33-2 SUMIDA CD54-330LC **AVX TPS SERIES
Figure 1. 3.3 V Powered Flash Memory VPP Generator
Figure 4. 5 V to 12 V Converter With Shutdown to 0 V at Output
L1 33 H* MBRS130T3
10 H* VIN 2V 22 F +
3 1
MBRS130T3 12V 35mA
3
VIN
SW
SENSE 8
ADP1109A-12
7
VIN 3V
1
VIN
SW
FB 8 R2 250k R1 40.3k +
ADP1109A
7
VOUT 9V
SHUTDOWN GND PGND
5 4
SHUTDOWN GND GND
5 4
+ 33 F** 25V SHUTDOWN
SHUTDOWN *COILTRONICS CTX10-1 SUMIDA CD54-100LC **AVX TPS SERIES
C1 22 F** 16V
*COILTRONICS CTX33-2 SUMIDA CD54-330LC **AVX TPS SERIES
Figure 2. 2 V Powered Flash Memory VPP Generator
Figure 5. 3 V to 9 V Converter
10 H* VIN 2V 22 F +
3 1
MBRS130T3 5V 110mA
VIN
SW
SENSE 8
ADP1109A-5
7
SHUTDOWN GND PGND
5 4
+ 33 F** 10V
SHUTDOWN *COILTRONICS CTX10-1 SUMIDA CD54-100LC **AVX TPS SERIES
Figure 3. 2 V to 5 V Converter
-4-
REV. 0
ADP1109A
170
OSCILLATOR FREQUENCY - kHz
68
1.4 1.2
SATURATION VOLTAGE - V
150
DUTY CYCLE - %
65
1.0 0.8 0.6 0.4 0.2
130
VIN = 5V VIN = 3V
62
110
59
90
VIN = 2V
70 50 -40
56
0
25 70 TEMPERATURE - C
85
53 -40
0
25 70 TEMPERATURE - C
85
0.0 0.1
0.2
0.4 0.6 0.8 ISWITCH CURRENT - A
1
1.2
Figure 6. Oscillator Frequency vs. Temperature
Figure 7. Duty Cycle vs. Temperature
Figure 8. Saturation Voltage vs. ISWITCH Current in Step-Up Mode
0.60 0.55 0.50 0.45
VCE(SAT) - V
6.0 VCE(SAT) @ VIN = 3V AND ISW = 0.65A
SWITCH-ON TIME - sec
600 550
5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 -40 0 25 70 TEMPERATURE - C 85
QUIESCENT CURRENT - A
500 450 400 350 300 250 -40
0.40 0.35 0.30 0.25 0.20 0.15 0.10 -40 0 25 70 TEMPERATURE - C 85
0
25 70 TEMPERATURE - C
85
Figure 9. Switch Saturation Voltage vs. Temperature
Figure 10. Switch-On Time vs. Temperature
Figure 11. Quiescent Current vs. Temperature
12.20 12.15 12.10
OUTPUT VOLTAGE - V QUIESCENT CURRENT - A
600
500
12.05 12.00 11.95 11.90 11.85 11.80 11.75 11.70 -40 0 25 70 TEMPERATURE - C 85
400
300
200
2
4
6 8 10 12 14 16 INPUT VOLTAGE - Volts
18
20
Figure 12. 12 V Output Voltage vs. Temperature
Figure 13. Quiescent Current vs. Input Voltage
REV. 0
-5-
ADP1109A
APPLICATION INFORMATION
THEORY OF OPERATION
considered for battery powered and similar applications where the input voltage varies. To minimize Electro-Magnetic Interference (EMI), a toroid or pot core type inductor is recommended. Rod core inductors are a lower-cost alternative if EMI is not a problem.
Calculating the Inductor Value
The ADP1109A is a flexible, low power switch-mode power supply (SMPS) controller for step-up dc/dc converter applications. This device uses a gated-oscillator technique to provide very high performance with low quiescent current. For example, more than 2 W of output power can be generated from a +5 V source, while quiescent current is only 360 A. A functional block diagram of the ADP1109A is shown on the front page. The internal 1.25 V reference is connected to one input of the comparator, while the other input is externally connected (via the FB pin) to a feedback network connected to the regulated output. When the voltage at the FB pin falls below 1.25 V, the 120 kHz oscillator turns on. A driver amplifier provides base drive to the internal power switch, and the switching action raises the output voltage. When the voltage at the FB pin exceeds 1.25 V, the oscillator is shut off. While the oscillator is off, the ADP1109A quiescent current is only 460 A. The comparator includes a small amount of hysteresis, which ensures loop stability without requiring external components for frequency compensation. A shutdown feature permits the oscillator to be shut off. Holding SHUTDOWN low will disable the oscillator, and the ADP1109A's quiescent current will remain 460 A. The output voltage of the ADP1109A is set with two external resistors. Three fixed-voltage models are also available: the ADP1109A-3.3 (+3.3 V), ADP1109A-5 (+5 V) and ADP1109A-12 (+12 V). The fixed-voltage models are identical to the ADP1109A, except that laser-trimmed voltage-setting resistors are included on the chip. On the fixed-voltage models of the ADP1109A, simply connect the SENSE pin (Pin 8) directly to the output voltage.
COMPONENT SELECTION General Notes on Inductor Selection
Selecting the proper inductor value is a simple two step process: 1. Define the operating parameters: minimum input voltage, maximum input voltage, output voltage and output current. 2. Calculate the inductor value, using the equations in the following section.
Inductor Selection
In a step-up, or boost, converter (Figure 1), the inductor must store enough power to make up the difference between the input voltage and the output voltage. The inductor power is calculated from the equation: P L = VOUT +V D -VIN ( MIN ) x IOUT
(
)( )
(1)
where VD is the diode forward voltage ( 0.5 V for a 1N5818 Schottky). Energy is only stored in the inductor while the ADP1109A switch is ON, so the energy stored in the inductor on each switching cycle must be must be equal to or greater than:
PL f OSC
(2)
in order for the ADP1109A to regulate the output voltage. When the internal power switch turns ON, current flow in the inductor increases at the rate of:
IL t =
When the ADP1109A internal power switch turns on, current begins to flow in the inductor. Energy is stored in the inductor core while the switch is on, and this stored energy is then transferred to the load when the switch turns off. To specify an inductor for the ADP1109A, the proper values of inductance, saturation current and dc resistance must be determined. This process is not difficult, and specific equations are provided in this data sheet. In general terms, however, the inductance value must be low enough to store the required amount of energy (when both input voltage and switch ON time are at a minimum) but high enough that the inductor will not saturate when both VIN and switch ON time are at their maximum values. The inductor must also store enough energy to supply the load, without saturating. Finally, the dc resistance of the inductor should be low, so that excessive power will not be wasted by heating the windings. For most ADP1109A applications, an inductor of 10 H to 47 H, with a saturation current rating of 300 mA to 1 A and dc resistance <0.4 is suitable. Ferrite core inductors that meet these specifications are available in small, surface-mount packages. Air-core inductors, as well as RF chokes, are unsuitable because of their low peak current ratings. The ADP1109A is designed for applications where the input voltage is fairly stable, such as generating +12 V from a +5 V logic supply. The ADP1109A does not have an internal switch current limiting circuit, so the inductor may saturate if the input voltage is too high. The ADP1111 or ADP3000 should be -6-
()
- R't V IN 1- e L R'
(3)
where L is in Henrys and R' is the sum of the switch equivalent resistance (typically 0.8 at +25C) and the dc resistance of the inductor. In most applications, the voltage drop across the switch is small compared to VIN so a simpler equation can be used:
IL t =
()
V IN t L
(4)
Replacing t in the above equation with the ON time of the ADP1109A (5.5 s, typical) will define the peak current for a given inductor value and input voltage. At this point, the inductor energy can be calculated as follows:
1 E L = L x I 2 peak 2
(5)
As previously mentioned, EL must be greater than PL/fOSC so that the ADP1109A can deliver the necessary power to the load. For best efficiency, peak current should be limited to 1 A or less. Higher switch currents will reduce efficiency because of increased saturation voltage in the switch. High peak current also increases output ripple. As a general rule, keep peak current as low as possible to minimize losses in the switch, inductor and diode. REV. 0
ADP1109A
In practice, the inductor value is easily selected using the equations above. For example, consider a supply that will generate 12 V at 120 mA from a +5 V source. The inductor power required is, from Equation 1: PL = (12 V + 0.5 V - 5 V) x (120 mA) = 900 mW On each switching cycle, the inductor must supply:
P L 900 mW = = 7.5 J f OSC 120 kHz
Capacitor Selection
For optimum performance, the ADP1109A's output capacitor must be carefully selected. Choosing an inappropriate capacitor can result in low efficiency and/or high output ripple. Ordinary aluminum electrolytic capacitors are inexpensive, but often have poor Equivalent Series Resistance (ESR) and Equivalent Series Inductance (ESL). Low ESR aluminum capacitors, specifically designed for switch mode converter applications, are also available, and these are a better choice than general purpose devices. Even better performance can be achieved with tantalum capacitors, although their cost is higher. Very low values of ESR can be achieved by using OS-CON capacitors (Sanyo Corporation, San Diego, CA). These devices are fairly small, available with tape-and-reel packaging, and have very low ESR.
Diode Selection
The required inductor power is fairly low in this example, so the peak current can also be low. Assuming a peak current of 600 mA as a starting point, Equation 4 can be rearranged to recommend an inductor value: L= V IN I L ( MAX ) t= 5V 5.5 s = 45.8 H 600 mA
Substituting a standard inductor value of 33 H, with 0.2 dc resistance, will produce a peak switch current of: I PEAK = 5V 1.0
-1.0 x 5.5 s 1- e 33 H = 768 mA
Once the peak current is known, the inductor energy can be calculated from Equation 5:
EL = 1 33 H x 768 mA 2
In specifying a diode, consideration must be given to speed, forward voltage drop and reverse leakage current. When the ADP1109A switch turns off, the diode must turn on rapidly if high efficiency is to be maintained. Schottky rectifiers, as well as fast signal diodes such as the 1N4148, are appropriate. The forward voltage of the diode represents power that is not delivered to the load, so VF must also be minimized. Again, Schottky diodes are recommended. Leakage current is especially important in low current applications, where the leakage can be a significant percentage of the total quiescent current. For most circuits, the 1N5818 is a suitable companion to the ADP1109A. This diode has a VF of 0.5 V at 1 A, 4 A to 10 A leakage, and fast turn-on and turn-off times. A surface mount version, the MBRS130T3, is also available. For switch currents of 100 mA or less, a Schottky diode such as the BAT85 provides a VF of 0.8 V at 100 mA and leakage less than 1 A. A similar device, the BAT54, is available in an SOT-23 package. Even lower leakage, in the 1 nA to 5 nA range, can be obtained with a 1N4148 signal diode. General purpose rectifiers, such as the 1N4001, are not suitable for ADP1109A circuits. These devices, which have turn-on times of 10 s or more, are far too slow for switching power supply applications. Using such a diode "just to get started" will result in wasted time and effort. Even if an ADP1109A circuit appears to function with a 1N4001, the resulting performance will not be indicative of the circuit performance when the correct diode is used.
(
)(
)
2
= 9.7 J
The inductor energy of 9.7 J is greater than the PL/fOSC requirement of 7.5 J, so the 33 H inductor will work in this application. By substituting other inductor values into the same equations, the optimum inductor value can be selected. When selecting an inductor, the peak current must not exceed the maximum switch current of 1.2 A. If the calculated peak current is greater than 1.2 A, either the input voltage must be increased or the load current decreased.
Output Voltage Selection
The output voltage is fed back to the ADP1109A via resistors R1 and R2 (Figure 5). When the voltage at the comparator's inverting input falls below 1.25 V, the oscillator turns "on" and the output voltage begins to rise. The output voltage is therefore set by the formula:
R2 VOUT = 1.25 V x 1+ R1
Resistors R1 and R2 are provided internally on fixed-voltage versions of the ADP1109A. In this case, a complete dc-dc converter requires only four external components.
REV. 0
-7-
ADP1109A
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
0.430 (10.92) 0.348 (8.84)
8 5
0.1968 (5.00) 0.1890 (4.80)
8 1 5 4
0.280 (7.11) 0.240 (6.10)
1 4
PIN 1 0.210 (5.33) MAX 0.160 (4.06) 0.115 (2.93)
0.060 (1.52) 0.015 (0.38) 0.130 (3.30) MIN SEATING PLANE
0.325 (8.25) 0.300 (7.62) 0.195 (4.95) 0.115 (2.93)
0.1574 (4.00) 0.1497 (3.80)
0.2440 (6.20) 0.2284 (5.80)
PIN 1 0.0098 (0.25) 0.0040 (0.10)
0.0688 (1.75) 0.0532 (1.35)
0.0196 (0.50) x 45 0.0099 (0.25)
0.022 (0.558) 0.100 0.070 (1.77) 0.014 (0.356) (2.54) 0.045 (1.15) BSC
0.015 (0.381) 0.008 (0.204)
SEATING PLANE
0.0500 0.0192 (0.49) (1.27) 0.0138 (0.35) BSC
0.0098 (0.25) 0.0075 (0.19)
8 0
0.0500 (1.27) 0.0160 (0.41)
-8-
REV. 0
PRINTED IN U.S.A.
C3183-8-10/97
8-Lead Plastic DIP (N-8)
8-Lead SOIC (SO-8)

▲Up To Search▲

Price & Availability of ADP1109A

	To Download ADP1109A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .